Adjust The Focus In A Video

When you are filming a subject with a digital video camera, some part of the camera frame will be in focus while another part will not be. Typically, you want your subject to be in perfect focus while the background takes up most of the out-of-focus area. There are a few things you can do to adjust the focus while filming a video.

Instructions

1. Point the lens of your camera directly at the subject you are trying to film.

2. Look through the view finder on your camera and manually rotate the focus ring on the lens to the left and right to adjust the focus (for cameras that focus via the lens). Continue to look through the view finder and adjust the focus until the subject is in focus and the background is out of focus.

3. Press and hold the "Focus" button on the digital camera's key pad (for cameras that focus via the key pad). Holding down the button will begin to increase and decrease the focal point. Look at the digital screen or through the view finder on the camera until the subject is in focus. Remove your finger from the "Focus" button.

4. Move your camera closer or farther away from your subject (to adjust focus without changing settings on your camera). You can also have the subject physically move farther or closer to the camera. Look through the view finder or into the digital screen until you find the point where the subject becomes focused.

Tags: through view, through view finder, view finder, your camera, focus while, adjust focus

Use Endoscopes

An endoscope is a piece of highly integrated medical equipment that is used to visualize the inside of a body part, either through an existing orifice or a created one. An endoscope contains a light and a small camera to record the internal images. An endoscope also contains small pinchers that are used to obtain specimens for biopsy. The trend nowadays is to use disposable one-time-use endoscope tubes to prevent cross contamination, due to the endoscope tubes being hard and expensive to sterilize. We will go over a basic stomach endoscopy.

Instructions

1. Place the patient on an NPO (nothing by mouth) diet for at least eight hours before the procedure is to be done.

2. Place the patient on his back with a neck roll under the neck to tilt the head back for easier insertion of the tube.

3. Spray the patient's throat with a numbing agent to help relax the throat muscles and decrease the natural gag reflex. Have the patient hold his breath before spraying the agent to prevent it from going down into the lungs.

4. Lubricate the entire length of the endoscope tube with the water-based lubricant. This will help with the insertion of the tube.

5. Have the patient open his mouth and hold his breath. Instruct him to swallow as you insert the endoscope tube, as this deactivates the gag reflex and helps increase patient comfort during the tube insertion.

6. Insert the endoscope tube through the patient's mouth, into his throat and down into the esophagus. Use the camera of the endoscope to guide you to be sure you don't go into the lungs. If you accidentally go into the lungs, the patient will usually start coughing. If this happens, withdraw the tube and begin again.

7. Begin taking pictures when the area you want to look at is visualized using the camera attachment on the endoscope tool. Rotate the tube to obtain pictures from different angles.

8. Take samples of any suspicious areas or lesions with the attached biopsy tools. Withdraw the biopsy specimens and place them in containers to be sent to the lab for testing. Reinsert the biopsy tool if additional samples need to be taken.

9. Instruct the patient to take a deep breath and let it out slowly as you withdraw the endoscope.

10. Place the patient in a slightly elevated position and monitor him for several minutes for any complications. When stable, the patient may return to his room, or he may be released to go home if this was done as an outpatient procedure.

Tags: endoscope tube, into lungs, Place patient, down into, endoscope tubes, Have patient, hold breath

Make A Thumb Scanner Using A Camera

A fingerprint scanner views a picture of the little ridges on your fingers to identify the unique pattern that is yours alone. You can make a digital camera into a "thumb scanner" that will save a picture of the fingerprint taken. The procedure relies on the macro setting of the digital camera -- selected from the menu settings -- which enables the lens to focus extremely close-up to an object. The digital camera will not be damaged in any way by using it as a thumb scanner.

Instructions

1. Open the battery compartment lid of the digital camera and insert new batteries. Close the lid. Open the memory card slot on the side of the camera and insert a compatible memory card into the slot. Close the lid. If the battery compartment also has a space for the memory card, skip this separate step.

2. Press the digital camera's "On" button. Press the "Menu" button that is typically located on the back of the camera next to the LCD viewing panel.

3. Select the "Lens" menu or a comparable menu -- the actual name will vary depending on the make of the camera. Select the "Macro" setting. Press the "Menu" button again to exit the settings.

4. Press the "Flash" button, or press the tab next to a flash icon to temporarily discontinue the use of the automatic flash feature. In some cases, activating the macro feature will automatically turn this off.

5. Place the camera on a table with the lens facing up. Place one of your thumbs in front of the lens, a few inches away. Press the shutter button on the digital camera halfway down to lock the focus of the thumb -- typically a "beep" will be heard to indicate that the focus is now locked.

6. Press the shutter button the rest of the way down to take a picture. Stand the digital camera up after the picture has been taken. Press the "Menu" button. Select the "Playback" feature and on the LCD screen you can see the picture that was just taken.

7. Select the thumb picture from the rest of the thumbnail pictures displayed on the LCD screen. View the picture of the thumb to verify that it is in focus -- if the thumb is not in focus, try taking another picture, moving the thumb closer or farther away than before. The thumb scan that your digital camera "thumb scanner" has taken can now be transferred to a computer via the memory card and viewed on a larger monitor screen or used with any security scanning program that you might have.

Tags: digital camera, memory card, Menu button, Press Menu, Press Menu button, thumb scanner, battery compartment

Reset A Password On The Nortel Nam Phone System

The Nortel NAM phone system uses the Norstar voicemail service. This phone system is ideal for large businesses that deal with customer service or inbound calls. The Norstar voicemail service allows you to use up to 1,000 mailboxes. It also includes 100 hours of voicemail storage. For businesses that continue to grow, the NAM system has 16 expandable channels. You need to use a password every time you access the voicemail service. It is highly recommended that you reset your password for added security and safety.

Instructions

1. Enter feature "983." Look for "LOG" on the display screen. Enter your login password.

2. Select the soft key under "MBOX." Press the soft key under "CHNG."

3. Enter the mailbox number. The display screen shows "Reset Password."

4. Select the soft key under "RESET." Press the release key. Your temporary password will be "0000."

5. Repeat Step One to log in. The display screen will prompt you to change your password. Press the soft key under "OK," when satisfied.

Tags: soft under, display screen, voicemail service, businesses that, Norstar voicemail

Buy Direct Tv Receivers

Satellite television can be a great addition to any home theater system. Being accessible almost anywhere and having generally low subscription fees, the Direct TV service is a popular choice. As an added bonus, the company offers several different receivers that can supplement and upgrade your viewing experience. Before you purchase a system, it is important to understand the features of each receiver and their cost.

Instructions

Researching and Purchasing a Receiver

1. Learn about the different receivers available. There are currently four versions: Standard, DVR, HD and HD DVR. Each receiver has unique features like high-quality picture, ability to record live television and advanced interfaces. Depending on the receiver you choose, the price may increase or decrease. It is important to keep this in mind while conducting your search.

2. Decide what features are important to you. Keep in mind that the receiver that you choose does not affect how you receive programming, only the experience.

The standard receiver allows for basic reception of programming on your television. There is not a special type of television set required for this receiver.

The high definition (HD) receiver is for users with HD-television sets. This will improve the quality of your picture to match your TV.

Choose the DVR receiver if you would like to record live television. It allows you to set times for recording, watch previous recordings and pause/rewind live television shows.

The HD/DVR receiver is a combination of the HD and DVR receivers. It allows for reception of HD broadcasts as well as the ability to record and play them back.

3. Call Direct TV if you're an existing customer wanting to upgrade. A representative will help you add the new equipment to your account and set up an appointment to have it installed. You can also find an authorized retailer to purchase a receiver. Direct TV has several affiliates that sell their receivers and other equipment. Choose the business you're most comfortable with and contact them for upgrade information.

4. Start a new service agreement. If you're completely new to Direct TV, you can get in touch with the company to start a new account. There are several options for doing this including over the phone, online and with an authorized retailer. Visit the Direct TV site to learn about the different methods for setting-up service.

5. After you've made your purchase and set up an installation appointment, you're all set. The Direct TV employee will ensure that your equipment is installed and working properly.

Tags: live television, ability record, about different, authorized retailer, different receivers, record live

Record Using The Lcd Monitor On A Camcorder

The easiest way to check what you're recording on a camcorder is by using the LCD monitor. The LCD monitor will give you a more accurate picture than the eyepiece. Using the LCD monitor on your camcorder is easy. Follow these steps to learn record using the LCD monitor on a camcorder.

Instructions

1. Turn your camcorder on by pressing the "Power" button.

2. Flip out the LCD screen. This should be located on one of the sides of your camcorder. To flip the LCD monitor out, you will need to either push or slide the latch holding it in place.

3. Make sure there is an image on your LCD monitor. If there is an image, your LCD monitor is working properly. If the monitor is blank, try closing and reopening it, and make sure you've taken off the lens cap.

4. Point the camera at the object you want to record and find it on the monitor. Reframe as needed, and make sure the object is in focus.

5. Press record and keep your subject in view on the monitor.

Tags: your camcorder, image your, image your monitor, make sure, monitor will, there image, there image your

Iphone 4g Features

First made available on June 24, 2010, the iPhone 4G initially priced out at $199 for a 16 GB model and $299 for a 32 GB model with a 2-year contract through AT&T. This model of the iPhone is known for its durability and high quality display. It boasts dual cameras and mics for improved quality and functionality.

Exterior Casing and Screen

At 9.3 millimeters thin, Apple claims the iPhone 4G to be the world's thinnest smart phone as of late 2010. The aluminosilicate glass exterior, which is the same material used for helicopter and high-speed train windshields, makes the iPhone 4G more durable and scratch resistant.

The 4.3 inch retinal display is 326 ppi (pixels per inch) with pixels so small that the naked eye cannot see individual pixels. This makes the iPhone 4G display the highest resolution smart phone screen in existence. According to Digital trends, this is four times the pixel density of the average LCD screen. The display is one of the larger screens on the smart phone market at 960 by 640 pixels.

The iPhone 4G's capacitive touch allows for multi-touch activities. This allows for features such as pinch to zoom and two-finger tap.

Hardware Specifications

The 5-megapixel camera has a backside-illuminated sensor designed to improve photo lighting by capturing more light in the sensor. The video feature also records HD videos at a 720 pixel resolution and captures 30 frames per second. The camera also allows for video chat. There is also a front-facing secondary camera built in.

The iPhone 4G has two microphones to enhance call quality. Next to the doc connector on the bottom of the phone is the main mic, used for phone calls, voice commands and audio memos. The second mic is located near the headphone jack on the top of the device; it is for face time calls and to help eliminate background noise during phone calls.

The iPhone's built-in rechargeable lithium-ion battery charges via USB to computer or through a power adapter. It allows for up to 7 hours of talk time or 300 minutes on standby. It runs an Apple A4 chip processor and has a 32 GB or 16 GB flash drive capacity.

Software

The iPhone 4G runs iOS 4 operating system, designed as the peer of the Android 2.1 operating system. The phone also includes a highly detailed photo and video editing software package. Software updates are available to improve the reception issues and other small operation issues. The advanced operating system allows users to sort applications into folders and allows for Web browsing via Safari browser.

Tags: operating system, smart phone, makes iPhone, phone calls

Battery Operated Home Security Camera Work

Why Use Battery Powered Security Cameras?

Battery powered security cameras are often used for personal or corporate security. They can provide excellent surveillance for areas that cannot be monitored at all times. There are two main reasons to use battery powered home security cameras. The first is that battery powered security cameras are not affected by power outages. This means that, as long as the batteries are regularly replaced, the camera will always be working. The other is that battery powered cameras do not need wires. This can be great for situations in which a wire cannot be hidden easily. This creates an advantage in that the camera's wires cannot be clipped, causing the camera to cease to work.

How Do Battery Powered Security Cameras Work?

Battery powered security cameras work without wires. Wireless security cameras make use of technology similar to closed-circuit television. As a result, the images are only available to a specific set or sets, not to the public. Wireless security cameras are made up of the specific camera, which has a transmitter, as well as a receiver, which records the video images. The images that wireless cameras capture are then sent via radio frequency to the receiver, which is connected to a time-lapse recorder or some other type of recording device. These images are then stored for later examination.

Advantages and Disadvantages

One of the main advantages of battery powered security cameras is that they are very difficult to disable. Unless the cameras can be physically broken, they will always record the images, as there are no wires that can be clipped. In addition, battery powered security cameras will be active even in the event of a power failure. One disadvantage of battery powered cameras is that the batteries must be replaced periodically. While this may not sound like a significant obstacle, keep in mind that any camera that is easily accessible is not a very secure camera. In addition, because battery powered security cameras are wireless, there are a limited number of radio frequencies that they can use, limiting the number of cameras that can be installed in any location.

Tags: battery powered, powered security, security cameras, battery powered security, powered security cameras

Use The Polaroid A520 Digital Camera

The Polaroid A520 is a compact digital camera suitable for everyday use. The A520 comes equipped with 5 megapixels of resolution, 4x digital zoom, 16 MB of built-in memory and the capacity to capture video at resolutions of up to 640 x 480 pixels (AVI format). Once properly configured, the procedure for taking pictures with the Polaroid A520 digital camera is very straightforward.

Instructions

1. Turn on the camera by pressing and holding the power button until the LCD screen activates. Examine battery icon in the lower-right corner of the LCD screen; if the icon indicates that battery power is low, replace the batteries before proceeding.

2. Press the mode button until you see a camera icon appear on the LCD screen. Press the flash button to cycle through the available options. Choose the icon of a lightning bolt with a letter "A" to set the camera to automatically determine when to use the flash; choose the icon of a lightning bolt with no letter "A" to set the camera to always use flash; choose the icon of an eye to set the camera to use the flash for red-eye reduction; choose the icon of a lightning bolt in a circle with a line through it to disable the flash completely.

3. Press the timer button to set the self-timer, if desired; you may choose between a two-second and a ten-second delay before the camera will capture an image.

4. Press the "M" button and navigate to the "Image Size" menu option; choose the desired resolution for your saved image file and press "OK." Press "M" and navigate to the "Quality" menu option and select your desired quality level; press "OK." Press "M" and navigate to the "Exposure" menu option and set your desired exposure levels; press "OK."

5. Use the buttons in the top-right corner of the camera to zoom in and out on your chosen subject. Look through the viewfinder and frame your image as desired. Press down on the shutter button and wait for the beep. Examine the LCD screen to review the picture you have taken.

Tags: choose icon, icon lightning, icon lightning bolt, lightning bolt, menu option

Tether A Windows Mobile

If you own a Windows Mobile phone with Internet capability, you can effectively share the Internet connection with your PC or notebook through a process called tethering. Tethering does not require any special software and you can connect your Windows Mobile phone to your computer through either a USB connection or Bluetooth wireless connection. While connected you have the ability to access the Internet on your computer as if it connected directly to the Internet, as long as your phone has a data signal.

Instructions

Tether Phone

1. Connect the Windows Mobile phone to your computer using the USB cable or pair the two devices using Bluetooth.

2. Press "Start" on the phone and scroll to "Programs." Select "Internet Sharing."

3. Choose "USB" or "Bluetooth PAN" (depending on how you connected the two devices) for the "PC Connection" field on the phone menu.

4. Select "My Connection3g" (or equivalent data connection for your network) for the "Network Connection" field on the phone menu.

5. Press "Connect" on the phone menu and wait 30 seconds for the device to connect.

6. Click "Start" and select "Connect To" on your computer. Select the Windows Mobile device.

7. Disconnect from the device by clicking the connection in the Windows icon tray on your computer and selecting "Disconnect."

Pair Computer and Phone Bluetooth

8. Click "Start" on your Windows Mobile phone and select "Settings."

9. Click the "Connections" tab and select the "Bluetooth" icon.

10. Place a check-mark next to "Turn on Bluetooth" and "Make this device visible to other devices."

11. Return to the "Settings" menu and select "Beam." Place a check-mark next to "Receive all incoming beams."

12. Click on "Start" on your computer and select "Control Panel."

13. Click the "Bluetooth Devices" icon and select the "Options" tab. Place check-marks next to all of the options. Click "OK."

14. Click the "Devices" tab and click "Add." Allow the "Add Bluetooth Wizard" to search for your phone.

15. Select your phone and click "Next" to pair the two devices.

Tags: Windows Mobile, your computer, Mobile phone, Windows Mobile phone, Click Start, phone menu

What To Do When Water Seeps Into Your Cell Phone Battery

Like most electronics, cell phones are highly susceptible to water damage. Once inside a phone, water can bridge the gap between different electrical contacts, creating short circuits that can damage or destroy a phone and its battery. Under the correct circumstances, you may be able to prevent or repair damage to your phone and its battery.

Remove the Battery

As soon as your phone's battery is exposed to water, remove it from the phone. Do not attempt to power-down the phone, simply open the phone's rear cover and remove the battery. Remove any other removable components, such as SIM cards or SD cards, as well. Do not attempt to power on your phone or charge its battery or you may further damage the battery and the phone.

Check for Evidence

Verify that the water damage to your phone actually permeated the battery. Dry the surface of the battery with a paper towel and check for more water leaking out from inside the battery. If the water did not penetrate to the inside of the battery, it is probably still functional. You can also check for a small white or red sticker on the battery or in the phone's battery compartment. If the sticker is white, large amounts of water did not penetrate to the inside of the phone. If the sticker has turned red, the inside of your phone has been exposed to water.

Dry

Fill a Tupperware container halfway with rice. Remove any removable faceplates from your phone and put all of the parts of the phone and your battery in the container. Fill the rest of the container with rice and seal it. The rice will draw the moisture out of your phone and battery. This is important to prevent short circuits when you power up your phone. Leave the phone in the sealed container for three days, then remove and reassemble the phone. Attempt to power your phone on; if it does not turn on, you may need to replace the battery or the entire phone.

Replace

If only the battery was exposed to water and the rest of the phone avoided major damage, you may be able to replace the battery and continue using the phone. You can purchase replacement batteries for most phones over the Internet in standard capacity and expanded capacity models. If the white water damage label on the battery or the inside of the phone remained white, you can send your phone back to the manufacturer if it is still under warranty. If the label changed to red, the manufacturer will not accept it.

Tags: your phone, phone battery, exposed water, inside phone, power your, power your phone

Diy Foamboard Reflector

Amateur or freelance photographers can build a reflector at home

Correct lighting is vital to good photography. It's something photographers need ways of managing. A reflector dissolves backlight problems by allowing you to control light sourcing. It does this by reflecting ambient light, or your camera's flash, off its surface and onto your subject. You change the lighting by moving the reflector.

Professional reflectors are expensive. You can build one at home, though, that does everything the professional models do and more; if you build it yourself, you can modify it. You won't get that flexibility out of a "pro" reflector.

Instructions

Constructing the Stand

1. Drill a 1/4-inch hole in the center of a T-connector, opposite the T-stem. This should fit snugly over the screw in your tripod. Tighten it with the wing-nut.

2. Push the 31-inch PVC pipe into the top of the T-connector. Put the last T-connector on top so that its lateral sockets point left and right.

3. Attach two 4-inch pipes into the remaining openings on the bottom T-connector, and two 6-inch pipes to the top.

4. Attach a 90-degree elbow to the end of each pipe. Insert a 2-inch pipe into the end of each elbow.

5. Attach an elbow connector to the two 2-inch pipes on the bottom. Make sure that these face forward: they support the foamboard from the bottom.

6. Attach 2-inch pipes to the two elbows on top of the frame, and attach the remaining two elbows to those. Make sure the elbows point to the sides.

7. Attach the last 4-inch pipes to the elbows on top.

8. Place the foamboard onto the frame. The bottom two elbows should support it like a bike rack, while the top two hold it in place.

Tags: 2-inch pipes, 4-inch pipes, Make sure, pipe into, pipes elbows

Use Photocells

Photocells are sensors that detect light. There are countless reasons why they are useful and more beneficial than standard lighting. First of all, they are small, which means they are easy to work with and use in different locations. Second, they are very inexpensive. They're also low-power and don't wear out, which makes them highly energy-efficient. There are also less obvious benefits to using photocells; security, for example. Photocell lighting can be "tripped" if it is walked past. Also, photocell lighting can be used to illuminate any signs or advertisements for your business at night.

Instructions

1. Obtain photo cells for your desired application, such as outdoor lighting, from Radio Shack or a similar electronics store.

2. Choose the ideal location for the photocells. This should be an area where the photocells will receive plenty of light, such as outside in the sunlight, near a lamp, or in a well-lit room.

3. Position the photocells so that they will not be affected by any temporary light sources, such as porch lights, car headlights or rarely used lamps. Make sure there are no obstructions that would prevent your photocell lighting from being visible at night. This is especially important if your photocell lighting is being used to illuminate a sign for your business.

4. Determine which calibration method to use. The normal calibration procedure is usually recommended and is automatic, so you should always calibrate this way.

5. Clean your photocells to remove any dirt and oil that may have been left by your fingertips, and clean them regularly for the best performance.

Tags: lighting from, photocell lighting, used illuminate, your business, your photocell, your photocell lighting

Troubleshoot The Dsc F717 Sony Camera

Use the supplied USB cable.

Sony's DSC-F717 is a digital still camera from Sony's Cyber-shot brand. The camera is also capable of capturing video. Problems with the cameras can be related to the battery pack and power; shooting still images and movies; viewing and editing images; flash memory; and computer connection issues. Problems with the Cyber-shot DSC-F717 can be solved by following some troubleshooting steps.

Instructions

1. Turn the camera off to charge the battery pack if the battery pack isn't charging. Look for the charge lamp. It's the lamp marked "CHG." If the lamp flashes, the battery pack isn't installed properly. Seat the battery pack properly. You should be able to easily close the battery compartment door. It's normal for the camera to turn off suddenly when running on battery power--it's a battery-saving measure.

2. Insert a memory stick if the camera won't record still images or movies. Insert the memory stick the right way. It inserts from the right side. Take a look at the Mode Dial and make sure it's not set to "SET UP" or on the arrow icon, which indicates Playback mode. The camera won't record in Playback mode or Setup.

3. Set the write protect switch on the Memory Stick flash memory to the recording position if the deleting or editing functionality won't work. The switch mustn't be on the "Lock" position.

4. Move the camera away from the television if the images are noisy. Noise shows as specks of light, snow or other unacceptable degradation. Any strong magnetic field can cause noise, including microwave ovens.

5. Connect the camera to the computer to view images full size if they're too small on the camera. Use the supplied USB cable. You may have to disconnect the cable and reconnect it again if the computer won't recognize the Sony DSC-F717 Cyber-shot camera right away.

Tags: battery pack, camera record, flash memory, images movies, Insert memory, Insert memory stick

View Blackandwhite Negatives

Viewing negatives properly requires a loupe or a light box.

Viewing black-and-white negatives before developing larger photo prints is a useful way of discarding unwanted images and selecting only the optimal shots. To view black-and-white negatives, you will need a light box or a loupe, depending on how much detail you wish to see before development. A light box is a flat, backlit surface, and a loupe is a type of hand-held magnifier that shows more detail and gives a better idea of what the negative will look like when printed as a larger photo. Viewing photo negatives is a simple process that amateur photographers can undertake.

Instructions

1. Hold the negatives only on the edges to avoid smudging them with fingerprints. Use this method whether you are using a light box or a loupe to view the negatives.

2. Switch on the light box so that its white surface is illuminated. Place the negatives in the center of the light box, where the most light emanates from. This will allow you to view the negatives.

3. Use a loupe to view the images in greater detail. Do this in a well-lit room. Hover the loupe slightly above the negatives to avoid damaging them.

4. Hold the negatives against a window as the sun shines through. This has an effect similar to that of the light box and does not require an amateur photographer to purchase any additional equipment.

Tags: black-and-white negatives, Hold negatives, larger photo, light loupe, loupe view, view negatives

Gps Locators For Children

Losing a child, even for a few seconds, can be terrifying for a parent. Even if you know where your children are, GPS locators can add peace of mind. There are various types of GPS tracking systems that are suitable for your child.

Statistics

Based on the FBI'S missing person statistics, there were 102,764 active missing persons as of December 2008. Of these missing persons, 49.7 percent were under the age of 18. With the increased uncertainty of society today, GPS locators can help parents address safety concerns.

GPS Watch

If you want to be discreet in tracking your children, a GPS watch might be the best option. Built-in trackers can help locate children. GPS watches look like many other digital watches and the purpose of the watch does not need to be known. With a GPS watch, notifications can be sent directly to your cell phone or email address with the location of the device. An extra feature on some GPS watches is a panic button with automatic tracing, which is beneficial if your child is hurt, feels insecure or is lost.

Wristbands or Ankle Bracelets

Wristband an ankle bracelets can provide a built in GPS device. These are often waterproof. These are often used for younger children because there are not any panic buttons, so younger children will not play with the device and send parents into a panic.

Voice Activated GPS

There are voice activated GPS locators that keep track of kids so that they can be monitored from home. The voice system will first alert parents. If parents are not able to be contacted, there will be an automatic alert sent to authorities. This is especially helpful if medical assistance is needed.

Concealed GPS Chips

If parents want to remain discreet in tracking their kids, a concealed GPS tracker can be placed or concealed in children's belongings, in a bag, the sole of his or her shoe or in another commonly used item. This tracker sends transmissions back to a cell phone or e-mail account, which you choose upon set-up. You also have the ability to choose the frequency and parameters for an update. For instance, if your child leaves the house in the middle of the night, you can have an update sent to you via instant message.

Considerations

When choosing a GPS locator for children, it is important to consider the transmission range, its ease of use, and whether false transmissions can be sent. The FCC started to require that cell phones have GPS capability if manufactured after 2005, so get an updated cell phone and remind your kids to call 911 in an emergency. Consider what features you do not want to give up and compare by cost and durability as well. Make sure that the GPS locator will last and not need to be replaced frequently. Although price may be an issue for many families, it is not possible to put a price tag on a child's safety.

Tags: cell phone, your child, discreet tracking, missing persons, These often, younger children, your children

Gloss Vs Matte Lcd

Gloss Vs. Matte LCD

Choosing an appropriate LCD screen can cause a dilemma when you are not aware of the differences between the types available. Being informed of the pros and cons of each LCD type will help you make the best choice to suit your personal needs and preferences.

Glossy LCD

Glossy screens provide a user with the most quality and highest levels of brightness and contrast. They are characterized by bright, vibrant colors and the displays are more crisp and clear than matte screens. Glossy screens can make viewing tiresome, however, as they do have a negative effect on the eyes and smudge very easily.

Matte LCD

Matte LCD screens use a polarized coating, which cuts down on glare. Hence they are called "anti glare" screens. The only disadvantages this type presents are that colors appear more dull than on a glossy screen and the image may look unclear or not well defined.

Matte or Glossy: A better option?

The biggest difference between glossy and matte LCD screens is glare. Glossy screens are more prone to reflect light; when the screen is dark, you're likely to see a reflection of your surroundings. Some users also note that colors on glossy screens sometimes appear less true than those on matte screens.

Tags: matte screens, Gloss Matte, Glossy screens, that colors

Text To A Music Cd

Burning CDs allows music listeners to arrange songs into personal playlists that can be listened to at their convenience. CDs can now be burned with text known as "CD-text." CD-text lists information about a song such as its title, artist and the album on which it appears. Many modern CD players, car audio systems and electronic music programs support the ability to display this information to the listener.

Instructions

Instructions

1. Open iTunes (see Resources section). Arrange the songs you would like to burn into one playlist. Most CDs can hold 700 MB, which is approximately 80 minutes of music.

2. Check that the information for each of the songs you wish to burn is accurate. To adjust song information---such as song title, album title or artist name---right-click the song and select "Get Info." Click the "Info" tab and adjust the information accordingly.

3. Insert the writable CD into your computer's disc drive. Cancel any pop-up menus that appear.

4. Open the playlist you wish to burn. Click and drag the songs so they are listed in the order in which you would like them to appear on your CD.

5. Click "Burn Disc" in the bottom right corner of iTunes.

6. Select the "Include CD Text" option. When this option is checked, click "Burn."

Tags: title artist, wish burn, would like

Change A Camera To Infrared

Infrared (IR) photography involves capturing invisible light to produce striking images. To change a digital single-lens reflex (SLR) camera to infrared, you can add a filter and make minor adjustments or you can modify the camera permanently.

If you're just starting to explore infrared photography, it is safer to choose the simpler and nonpermanent option, which will enable you to learn how infrared photography works while still allowing you to use your D-SLR camera for normal shooting.

Instructions

1. Check your digital SLR camera and lens to get the specifications for buying a new filter. The IR filter you buy must fit the lens well.

2. Buy the IR filter for your camera. There are numerous options on the market. The main difference lies in the range of wavelengths each IR filter lets through.

3. Put your camera on a tripod and compose your shot early on. Once the filter is attached to the lens, you will most likely see nothing in the viewfinder. An IR filter looks black, and it readily blocks the image you should see in the viewfinder.

4. Put the filter onto the camera lens.

5. Use manual exposure. The camera's exposure meter won't work correctly with this set-up. Moreover, exposure times for IR photography are very long, even in broad daylight. Benchmark exposure times are 10 to 30 seconds; thus, a tripod is vital for avoiding motion blur. This is why most IR photos have subjects that are not moving. Landscapes are popular subjects for IR photography not only because they are static but also because most living things are rich in infrared.

6. Set your camera to auto focus (AF). It will also help if you step down the aperture enough to get focus on the entire distance of your subject. Older lenses may have a special IR focus distance guide. However, modern auto focus lenses do not.

7. Choose the lowest ISO setting to keep the noise level as low as possible.

Tags: your camera, auto focus, camera lens, exposure times, infrared photography

Restore 8mm Film

8mm film reel

Restoring 8 mm film requires a combination of analog and digital methods. Many telecine houses offer custom 8mm transfer and restoration services, but with your old projector and some free and open-source video editing software, you can restore and reformat 8 mm film yourself. To restore your own 8 mm film, you must clean it by hand, project it onto a screen and record that projection with a digital video camera. Import the resulting video onto your computer and use free software to reduce grain and remove scratches.

Instructions

1. Attach the head leader to the take-up reel on the projector and wind the film onto it gradually, inspecting as you go.

2. Wipe any dirt, dust or fingerprints from the film using the lint-free cloth and film cleaner. Use a cotton swab dipped in film cleaner to spot-clean specific frames.

3. Peel off splicing tape that looks weak or damaged. Swab the film frames that were beneath the tape to remove any glue residue, then re-tape the splice on both sides with your splicer. Reinforce any broken sprocket holes with splicing tape.

4. Place your reels on the projector, and thread the head leader to prepare for playback.

5. Mount the videocamera on the tripod, and focus the lens on the screen. If you don't have a screen, use a clean white wall. If your wall is colored or textured (e.g. stucco), you can tape a sheet of watermark-free white paper to it, preferably with a whiteness rating of 92 or above.

6. Start the projector and record the film with your digital video camera.

7. Connect your video camera to your computer via firewire or USB cable and import the footage.

8. Download the latest version of VirtualDub (link in resources) and extract the .zip archive. Because VirtualDub is a standalone application, no further installation is necessary.

9. Download the MSU Old Film Restoration filter (link in resources) and extract it to the "plugins" directory within VirtualDub.

10. Launch VirtualDub, import your footage and run the Old Film Restoration Filter to reduce film grain and remove dust and scratches.

11. Export your completed, filtered video to any of a variety of common file formats.

Tags: video camera, with your, digital video, digital video camera, film cleaner, Film Restoration

Diy Telescope Pole Camera

DIY: Telescope Pole Camera

Pole cameras provide a different view and allow a unique photo composition. A pole camera system simply mounts a camera on an extendable shaft. The extended pole gives a bird's eye view to the photographs. The system is used by creative photographers, building inspectors and sports photographers. A telescoping pole camera system can be made by do-it-yourselfers with modest abilities and tools.

Instructions

1. Add a camera tripod head to the top of an extendable painters handle. The top of the handle includes an attachment bolt that fits to the paint roller. Commercial adapters are available to convert that fitting to the 1/4 inch bolt shaft common to the base of the tripod head.

2. Attach a padded rest plate about 1 foot below the tripod head using epoxy glue. This plate extends about 8 inches from the pole in all directions and is made from stiff closed cell material. The plate serves as bumper and keeps the camera from striking the ground if the pole is laid on the ground. The plate usually includes a mark indicating the direction the camera is pointed because it obscures the camera from view from directly below.

3. Attach a remote cable release to the camera. String the cable along the paint extension pole using cable ties every couple of feet to keep the cable from flopping about. Set the camera to fully automatic and angle the tripod head to provide a shot of the intended subjects.

Tags: tripod head, camera from, camera system, Pole Camera, pole camera, pole camera system

Features Of Laser Printers

Laser printers use laser beams to accurately place dots of toner on paper.

Laser printers generate crisp, clear and repeated images on various materials ranging from paper and cardboard to plastic and metal printing plates. A paper laser printer operates similarly to a copier in that light magnetizes specific areas on a drum, attracting magnetic-colored toner. The toner is then transferred to the paper and fused with a scorching hot roller. The difference between a laser printer and a copier is that the copier uses a light to reflect an image from an original to the drum surface. A laser printer uses a computer-controlled laser to expose the drum in a series of very small, precisely positioned dots. Once the drum is exposed it then picks up toner and transfers it to paper, then the combination is fused.

Resolution

Laser printer imaging paper can have various resolutions ranging from 300 laser dots per inch (dpi) to up to 1200 dpi. The laser produces smaller and smaller dots for corresponding increases in the number of dots per inch. Laser printer imaging paper rarely has resolutions exceeding 1200 dpi because the physical properties of the toner cannot be reduced to smaller particles.

As the resolution increases, so does the smoothness and clarity of the printed image. Smaller and smaller dots arranged in curves and gradients result in less jagged edges and more subtle changes in screens. The higher the resolution, the more shades of gray are available. Three hundred dpi laser printers can produce 16 shades of gray, while 1200 dpi printers can produce 128.

Speed

Laser-printer speed is rarely restricted by the mechanical ability to move the paper. Speed is determined by the laser's ability to image the drum for repeated passes. Also, laser-printer speeds are affected by the computing power available to process and translate the image for the laser. Laser printers have processors and random-access memory (RAM), just like the computer used to produce the original file. Some laser printers have hard drives for storing data such as font files and other necessary graphic files. All of these factors can affect the laser printer's speed, measured in pages per minute. A relatively slow laser printer may run at 12 to 16 pages per minute. Faster laser printers can reach speeds of over 60 pages per minute. These machines are used for high-end graphic production such as address mailers and advertising supplements.

Color

Color laser printers work identically to black-only laser printers with one exception. Instead of one drum and one toner, the printer has four: black, cyan (a light blue), magenta (a pinkish red) and yellow. The four lasers image four drums, and the sheet of paper passes each drum separately. Once all four toners are on the paper, it is fused. Color laser printers usually come in only 1200 dpi resolutions in order to produce accurate color. Also, color laser printers run at relatively lower speeds because of the complexity of aligning the paper for accurate color registration and multiple laser and toner operations.

Tags: laser printers, pages minute, accurate color, Color laser printers, copier that

Fix Your Etrex Legend

The Garmin eTrex Legend is a GPS navigation device for outdoors enthusiasts to use when walking, climbing, hiking or boating. The eTrex Legend provides information such as the user's current heading and the local elevation and temperature. The GPS is designed with a rugged case that can withstand dropping and shock; however, it is possible for the device to malfunction. For example, its screen may no longer display images or it may not respond to button presses. If this occurs, the GPS can be mailed to Garmin for repair.

Instructions

1. Notify Garmin's Technical Support department of the issue with your eTrex Legend. Contact a technician by calling 1-800-800-1020 or 913-397-8200. It is also possible to contact a technician via e-mail (see resources).

2. Copy the return material authorization (RMA) and dock numbers provided by the technician.You must include these numbers when returning the device.

3. Provide the eTrex Legend's serial number, your phone number and a return shipping address. If the device is found to be in warranty, the repair is free. If it is not in warranty, arrange for payment.

4. Send the eTrex Legend by mail to: Garmin International, 1200 E. 151st Street. Include the RMA and dock number on the following two lines, then write Olathe, KS 66062.

Tags: eTrex Legend, eTrex Legend

Canon Powershot Sd630 Tips

Canon PowerShot SD630

The Canon PowerShot SD630 is a compact camera capable of taking pictures at a six-megapixel resolution. Designed primarily for consumers who are looking for a portable camera to take with them on the go, the SD630 is packed with tons of features that make taking great pictures easy to do.

Auto-Focus

Use the auto-focus when taking pictures. Hold the shutter button halfway down to bring your subject into focus and then press the button the entire way to take a picture.

Scene Modes

Use the SD630's built-in scene modes to take better pictures under different conditions. Press the "Menu" button on the back of the camera and then select "Scene Settings" to select from the built-in choices. Scene settings in the SD630 include Snow, Beach, Underwater, Night Snapshot, and Fireworks.

Turn Off the Display

Turn the display off on your SD630 in order to conserve battery power. The LCD uses a tremendous amount of battery power. Turn the LCD off by pressing the "DISP" button on the back of the camera and use the traditional viewfinder to frame pictures to maximize the life of your batteries.

Self-Timer

Use the self-timer to get yourself in pictures. You activate the self-timer by pressing the icon on the back of the camera that looks like a broken circle. Then set your camera where you would like it to take a picture and press the shutter button. Once the shutter is pressed, you have ten seconds to get into the picture yourself before the image is captured.

Tags: back camera, battery power, button back, button back camera, Canon PowerShot SD630, PowerShot SD630

Pick Home Theater Seating

After buying a projector and screen and setting up all the proper cables for a home theater, you'll want to kick back and enjoy a movie on your new system. If you convert a den into your home theater, you'll probably avoid having to buy new furniture. However, you may want to buy new seats so more people can enjoy the new movie setup.

Instructions

Pick Home Theater Seating

1. Draw up a rough estimate of how many people on average will be viewing movies in your home theater. This number could just be your immediate family, plus an extra seat or two in case you have guests.

2. Measure the available space in your home theater before you look at seating. Remember that you'll want to position the seating at least 6 feet from the screen and even more if you have a large screen.

3. Head to a furniture store and look for recliner seats that are similar to movie theater designs. If you have a large budget, you can pick seating with perks like leather covering and matching tables for resting drinks and snacks.

4. Look for a small two or three-seat couch. Some people prefer to keep a couch directly in front of the projection screen and pick separate seating to set up on the sides.

5. Ask about staggered height couches if you want to set up rows of home theater seating. You can also build wooden platforms 12 inches and 24 inches high to place seating, giving your room a real theater feel.

Tags: home theater, your home, your home theater, enjoy movie, have large

Audiovox Dvd Portable Troubleshooting

Audiovox Electronics Corporation manufactures portable DVD players for viewing DVDs when you are away from home. The feature list for most Audiovox portable DVD players is the same. The difference between models is the size of the LCD screen. Audiovox portable DVD players will work as they should under most circumstances. You may encounter an occasional problem that prevents normal operation. By troubleshooting the device, you can often fix the problem, without the need of a service technician.

Instructions

1. Charge the internal battery if your Audiovox portable DVD player stops working. To charge the battery, plug the small end of the AC adapter into the "DC IN" jack on the back of the DVD player, and plug the opposite end into an electrical outlet. Slide the power switch to the "Off" position when charging the battery. You can run the DVD player from the AC adapter, if you choose.

2. Remove the DVD from the player if you are experiencing distorted video when playing back a DVD. Check the disc to ensure it is not warped or cracked. Take a clean, soft rag and wipe off the bottom of the disc to remove any debris or smudges. When cleaning the bottom of the disc, wipe from the middle of the disc outward to prevent damage. Use a light touch when cleaning the bottom of the disc. If you still have a distorted image, try another disc in the DVD player. If the second disc works, the problem is with the original DVD. If it doesn't work, you may need to have your DVD player serviced.

3. Replace the battery in the remote control if it no longer operates the DVD player. Remove the battery cover from the back of the remote control, discard the old battery and install a new CR2025 battery. Be sure to not block the remote control sensor when using the remote control.

Tags: remote control, Audiovox portable, bottom disc, portable players, Audiovox portable players, cleaning bottom

Replace A Bulb In A Jvc Projection Tv

All JVC projection TVs display images by shining a beam of light inside the TV to convert a small picture into a larger picture. The source of this beam of light is a lamp (or "bulb"), which has a limited lifespan and must be replaced every one to two years. Although you can have the lamp replaced by an authorized JVC repair specialist, you can also replace the lamp at home by following certain steps.

Instructions

1. Order a compatible replacement lamp from JVC. Order a replacement lamp from JVC's Accessory Store or a local authorized parts distributor to ensure that you obtain a compatible replacement lamp. To order a replacement lamp, you must have the lamp type and lamp code of your JVC projection TV, which can be found on the rear of the television.

2. Turn off the television and allow the bulb to cool. For safety reasons, turn off and unplug your television before accessing any of its internal components. Wait at least 20 minutes before attempting to replace the lamp so that it has time to cool down. If the back of the television is not warm or hot to the touch, it is safe to begin removing the lamp.

3. Unscrew and remove the lamp door. The lamp door on JVC projection TVs is located on the rear left of the television and is shaped like a square. Several warnings related to the lamp will be printed on the door. Use a Phillips-head or flathead screwdriver to remove the large screw, then remove the door.

4. Unscrew and remove the lamp assembly unit. After you have removed the lamp door, you will see the lamp assembly unit. Use a Phillips-head screwdriver to remove the two screws. One screw is on the top right corner of the unit and the second screw is on the bottom left corner of the unit. Detach the lamp assembly unit from the compartment by lifting the handle and pulling the unit away from the television.

5. Install the replacement lamp and secure the lamp door. Hold the replacement lamp assembly unit by the handle and insert it straight into the compartment. Reinsert and tighten the two screws onto the lamp assembly unit with a screwdriver. Place the lamp door back onto the television and tighten the screw to secure it to the television.

6. Reset the television's lamp timer. Press "Menu" on the television's remote, then scroll to and select "Lamp Timer Reset." Press "OK" to rest the timer. A prompt will appear notifying you that the timer has successfully been reset.

Tags: replacement lamp, assembly unit, lamp assembly, lamp assembly unit, lamp door, beam light, compatible replacement

Ford Audio Troubleshooting

Ford cars and trucks are equipped with audio units that have several optional systems: radio, cassette tape, compact disc player and MP3 player, and different equalizer and speaker combinations. No matter the model car or truck you have, troubleshooting problems with your Ford audio systems involves three basic parts: console, recorded music player and speakers. Determining where you have a problem is the first step to deciding what to do make it like new: repair or replace.

Radio

Before doing any disassembly or other intrusive actions, just make sure the outside antenna is not broken or disconnected. A Ford audio receiver cannot pick up any FM station without an antenna. If necessary, look inside the body panel to make sure the wires to the antenna are connected. If your Ford has the antenna in the windshield (two small wires inside the glass), see whether the glass is chipped or cracked, or whether the wires are broken.

If you have a satellite antenna on the top of your Ford automobile, make sure the antenna wires are connected. You may have to unfasten the roof liner in the passenger compartment for this procedure. To check the radio unit, you will have to disassemble the dashboard. Although time-consuming, this is not complicated. All the screws are along the bottom and side and there are clips to unfasten and remove the dashboard. Take out the radio console and check that the "ext. ant" connection is secure.

Recorded Audio Player

If you cannot play tapes, CDs or MP3s, you should check the unit while you have the dashboard disassembled. Make sure the power cord and all the speaker wires are connected. Make sure the recorded audio player is functioning, the tape spools turn and the CD mechanical operation functions properly. If you cannot play MP3s, make sure the audio input jack is connected and no wires are broken or frayed. A bare wire touching metal can cause systems to not operate correctly.

Speakers

If you have no sound, or static, you need to check the speakers. These are under the dashboard cowl right behind the windshield, or under the front doors or possibly the back doors, depending on the Ford model cal you have, and the backseat bonnet near the back window. Ford SUVs can have bass response speakers located to the rear near the lift gate. Check the speakers for proper connections. Check to see whether the speaker is "blown." This happens when speakers are old or you play the volume really loud. The paper cone in the speaker (the thin black center) can become damaged. Any damage to a speaker will mean replacing the unit. This is done easily by just unscrewing the fasteners, disconnecting the wire and installing a new speaker. No component of a Ford audio system requires any soldering for connections. Everything is done with screws and tabs.

Tags: make sure, your Ford, cannot play, Ford audio, wires broken

Convert Cassettes To Digital

Immortalize your favorite cassettes in digital form. When you convert you old cassette tapes into digital audio, you'll have a secure electronic archive that won't deteriorate like cassettes. You'll also have option of emailing the files, editing and enhancing them or burning them to a CD or DVD--read on to find out just how easy it is.

Instructions

1. Insert the cassette into the cassette player. Connect one end of the 1/8" audio cable into the "Line Out" port on the cassette player. If the player doesn't have a line out port, plug the cable into the headphone port.

2. Plug the other end of the 1/8" audio cable into the "Line In" port on your computer's sound card.

3. Download a free copy of GoldWave, an audio-editing program, and then install it (see Resources). Open the program after the installation process has completed.

4. Click the "New" icon in the top left corner. In the "New Sound" menu, use the drop-down menus to set your recording's length and quality. When you're done, click "OK."

5. Press the red "Record" button in the floating "Control" menu located to the left of the main GoldWave menu and then press "Play" on the cassette player. When the recording is done, click the red "Stop" in the "Control" menu.

6. Click "File" in the upper left-hand corner of the main GoldWave menu and select the option "Save As" from the list.

7. Enter a name for the file in the the field labeled "File Name." Choose a file type to save the recording as from the drop-down menu labeled "Save As Type." Click the "Save" button when you're done.

Tags: cable into, cassette player, audio cable, audio cable into, cable into Line

Types Of Film Cameras

Film cameras have developed throughout the years and are still often used by artistic photographers despite the digital revolution.

The pinhole camera was invented around 1000 A.D., but it wasn't until 1827 that Joseph Nicephore Niepce was able to record the first photographic images, which disappeared shortly after they were created. In 1889 flexible roll film was created and paved the way for the mass produced film cameras. Today, film cameras come in a variety of styles and use many film formats.

Viewfinder Cameras

Also called box cameras, viewfinder cameras use a viewfinder separate from the lens to view the subject. These cameras have a limited aperture control and a single speed shutter. Point and shoot cameras, the type most commonly used for general snapshots, are viewfinder cameras.

Range Finder Cameras

Like viewfinder cameras, the range finder cameras use a viewfinder separate from the lens to see the subject. However, range finders show two images that come together when they are in focus.

Single Lens Reflex Cameras

Also simply called SLR cameras, these use the same lens for viewing the subject and taking the picture. SLRs are the most popular camera among professional photographers and photography students or enthusiasts. They allow the photographer to control the aperture and shutter speed and to swap lenses for various situations.

Twin Lens Reflex Camera

These cameras have separate viewing and taking lens. The picture is using viewed from above with the camera held at waist level. They use medium format film, which is larger than the standard 35mm film. Unlike SLRs, twin lens cameras have not become widely available in digital format, leaving film as the primary medium for this camera.

View Cameras

The view camera, one of the earliest developed working film cameras, is still in use today but only by high end professional and portrait photographers. These cameras come in a large variety for various situations. They use large format film, which is usually loaded one sheet at a time with one photograph per sheet. Although, some are able to use roll film with a special roll film holder.

Instant Cameras

Introduced and popularized by Polaroid, these cameras use film that contains the chemicals to develop and fix itself allowing the picture taker to have the developed photograph right after taking it. While the quality of these pictures is often unpredictable, the instant camera has a varied cult and art following as well as a great appeal for kids as a "toy" camera.

Tags: cameras have, cameras viewfinder, roll film, These cameras, called cameras

Speakers Cone Work

Introduction

You've been listening to music for years, but have you ever really thought about how a speaker actually creates sound? The speaker cone is the heart of the speaker and provides essential conversion so that you're able to hear all those songs that you love.

Speaker Dynamics

A speaker is actually a simple device when broken down. Essentially, there is a series of drivers each of which contains a magnet, an oscillating electromagnetic coil and a cone, usually composed of composite, metal or paper. Individual drivers are used for different frequency ranges. A tweeter is used for high frequencies, a woofer for low frequencies and a mid-range driver for those frequencies between the highs and lows. Additional drivers can be used to further break down frequencies and enhance the sound.

Sound

An amplified signal sent from a stereo amplifier drives the speaker. The AC signal, which contains the audio information of your CD or other recording, causes the electromagnetic coil to oscillate back and forth. An alternating current (AC) is one that constantly changes directions. As current reverses directions, the polarity of the electromagnetic coil also reverses, which causes it to alternate between repelling and attracting to the stationary magnet. This constant repel and attract cycle drives the oscillation of the coil. As the coil oscillates, it vibrates the speaker cone, which in turn vibrates air molecules, sending sound to your ears. In this way, the speaker cone reproduces the distinct frequencies contained within any recording.

Tags: electromagnetic coil, speaker cone, drivers used, speaker actually, which contains

Power A Car Amplifier With A Power Supply

Powering a car amplifier with a power supply, such as a charged car battery, requires two steps. The amplifier acts as any circuit and needs negative and positive supplies in order to work. The power wire, equipped with a fuse, runs all the way up to the car battery and connects to the positive terminal, completing the positive supply. The ground wire bolts directly to the vehicle's body, completing the negative supply, thus powering the amplifier.

Instructions

Connecting the power wire

1. Connect the power wire to the amplifier by plugging in the power wire's amplifier input into the amplifier's power output. It should be labeled on the amplifier, but if not, refer to the amplifier's wiring diagram for the power wire output's location.

2. Disconnect the negative terminal from the battery for safety reasons and run the power wire along to the front of the vehicle underneath the dashboard area, such as near the brake and acceleration pedals.

3. Fold the carpeting back if necessary and look for a hole in the vehicle's body that will allow you to run the power wire through into the engine bay. You may have to cut a hole through the firewall with an X-Acto knife in order to complete this step.

4. Run the power wire through the hole and into the engine bay and connect the power wire's power source input to the positive terminal on the battery. You can do this by disconnecting the positive terminal and bolting it back on over the power wire's power source input. Install a rubber grommet around the hole to prevent water from leaking into the interior.

5. Connect the fuse to the power wire if necessary by plugging it in. Most power wires already have the fuse connected. The fuse should be installed as close to the battery as possible because in the case of a short circuit, the wire will burn up to the point of the fuse.

Connecting the ground wire

6. Mount the amplifier in a cool, well-ventilated area such as the trunk to prevent overheating.

7. Connect the ground wire's amplifier input to the amplifier. Refer to the amplifier's wiring diagram if you can't figure out where the ground output is located.

8. Find a nut or screw within 18 inches of the amplifier. This is what you'll connect the ground wire to.

9. Unscrew the nut or screw and chip away any paint on the body of the vehicle around the screw to give the ground wire direct access to metal.

10. Place the ground wire's lead, which is shaped like a circle, over the hole the nut or screw was bolted into and bolt the nut or screw back over the ground wire to complete the circuit.

Tags: power wire, ground wire, positive terminal, wire amplifier, amplifier input

Find Out Which Video Formats Are Supported On A Palm Tungsten E2

To find out which video formats are supported on a Palm Tungsten E2, check product specifications provided in the User Guide. The Palm Tungsten E2 uses RealPlayer and Windows Media Player 10/DirectX desktop applications for video playback of individual files like DVD and CD formats. Follow these steps to learn find out which video formats are supported on a Palm Tungsten E2.

Instructions

1. Locate "Media specifications" on the outside of the box. Also try your paperwork included with your Palm Tungsten E2.

2. Inspect your paper work carefully. Visit the Palm Web site for information on the Palm Tungsten E2.

3. Visit the Microsoft download center where you will see that only genuine Windows files are accepted by Windows Media Player 10/Direct X. The Direct X validation system means that each file will be checked by Windows Media Player to be sure they are real Windows files.

4. Visit the Microsoft Windows Media Player support page. Then find out which video file formats are supported by Windows Media Player 10.

5. Remember that additional information sent with video files, such as play lists and text files, may come in different formats but are still readable by Windows Media Player 10.

6. Check "Real Player help" to find out which file types are supported on your Palm Tungsten E2. The typical Real Player application can play MP3, Real Media and WAV format files.

7. Start the "Real Player program" on your Palm Tungsten E2. Under the Tools menu, select "Preferences > Content" and then "Media Types." Read the information provided on the right-hand side of the window.

Tags: Palm Tungsten, Media Player, Windows Media, Windows Media Player, find which

Hook Up A Capacitor To An Amp

Capacitors store power for quick release in electronic circuits. They're extremely useful in power supplies for regulating and smoothing out power flow, ensuring the circuits of an electronic device get the power they need when demand is high. External capacitors are often added to car amplifier circuits so that the amp receives a steady supply of power when demand is high, as when a system with subwoofers is being driven at a loud volume setting.

Instructions

1. Disconnect the power cable running to your amplifier from the car's battery.

2. Cut the power cable running to the amplifier at a spot about 2-3 feet from the amplifier. Strip the wire so that 1/2 inch of bare wire is exposed and crimp a ring terminal onto the wire at both sides.

3. Connect the power cable to the capacitor on the terminal marked "+". The exact type connector varies according to the brand of capacitor, but it's common to have to loosen a screw, slide the ring terminals onto the post, and then tighten down.

4. Cut a length of ground cable long enough to reach a grounding point on your car's body. The spot where the amp is grounded is a good option, or you may choose another spot where you can connect to bare metal.

5. Place a ring terminal on both ends of the wire, and attach one end to the capacitor and another to the ground location. Your capacitor is now connected to the amplifier.

Tags: power cable, cable running, demand high, power cable running, ring terminal, spot where

Buy A Fisher Home Cd Player

There are many different online and physical stores where you can purchase a Fisher home CD player. However, there are some stores that offer Fisher products made for convenience and ease of use, and there are other places where you are likely to find higher-quality "audiophile" Fisher CD players and stereo equipment. Buying a Fisher home CD player is easy -- knowing where to look for the right type of CD player is the hard part.

Instructions

Buying a Fisher Home CD Player

1. Determine what you really need from the unit you will purchase. For example, you may need a unit that can fit into a small area, or you may be looking for a very high-quality CD player. Figure out how much you are willing to spend on the CD player.

2. Check www.amazon.com for small, convenient CD players. Amazon.com is a good place to look for a Fisher CD player for a small kitchen, child's room or home office.

3. Search www.ebay.com for a Fisher CD player. Ebay is an auction site that allows users to bid on items for sale by private parties or businesses. Ebay is a particularly good place to find used or discontinued Fisher products like the Studio Standard Series.

4. Check online classifieds ads in your area at www.craigslist.org. People often sell CD players for much less than they are worth simply to get rid of an unused or unwanted items. Most items sold on Craigslist are sold by individuals, but business do post special deals as well.

5. Visit local retail stores like Target (www.target.com) and Best Buy (www.bestbuy.com). Large retail stores often have special sales that will allow you to purchase an item for much less than its normal retail price. The Christmas season is often the best time to purchase a CD player, as they are usually on sale to encourage buyers to purchase them as gifts.

Tags: Buying Fisher, Fisher home, Fisher Home Player, Fisher home player, Fisher player, Fisher products

Install An Addon Car Cd Changer

Installing an add-on car CD changer may be the perfect solution for those who lease or rent vehicles--or plan on using one changer for two or more vehicles. Add-on car CD changers are generally easy to install and require less installation expertise than most other mobile sound systems.

Instructions

1. Decide on the proper location for your new add-on CD changer. While many people choose the trunk or underneath one of the front seats, you may be able to get more creative, depending upon both the size of your vehicle and the actual size of the changer. Take into account the length of the associated cables supplied with the changer so you can avoid having to purchase additional leads and interfaces.

2. Read the owner's manual of your add-on car CD changer thoroughly before beginning any installation. Not only will the owner's manual give you specific tips on install the changer and associated cabling, but it will give you a complete inventory of all the mounting hardware and decide which combination of accessories and adapters to use.

3. Determine whether you want to use the supplied bracket and hardware for a more permanent type of installation for your add-on CD changer or Velcro straps if you want the option to remove the changer without modifying or otherwise damaging the vehicle. Velcro straps are usually offered free from the car audio retailer who sold you the changer.

4. Check out the factory-installed or existing car audio system and see how an add on car CD changer will be installed. You may need to purchase a separate CD interface, which consists of a wiring harness and associated cabling, if your present unit does not provide the right type of output jacks for your new changer.

5. Choose proper pathways for all of the cabling of your new changer so that they are hidden from view and will not be damaged. Most carpeting in modern vehicles can be easily pried up and then replaced by carefully using a flathead screwdriver.

Tags: add-on changer, your add-on, your add-on changer, associated cabling, cabling your, owner manual, Velcro straps

Transfer An Sd Memory Card And A Vhs To A Dvd

Transfer an SD Memory Card and a VHS to a DVD

Transferring the contents of an SD memory card or VHS tape to DVD requires several pieces of hardware, software and media. These must all be compatible in order to move your data to its final destination in a usable form.

Instructions

SD Memory Card to DVD

1. Place SD memory card into SD slot on computer. If there is none, buy and connect SD memory card reader into USB slot via USB cable. If your SD is High Capacity (SDHC), then the slot must also be a compatible SDHC slot.

2. Wait for pop-up wizard to show you the contents of the SD card on your computer screen. Otherwise, search for the SD card contents under the "Computer" folder.

3. Burn non-video data by copying the SD memory card files to the drive letter of your DVD burner drive. Burn the data to the drive containing your blank recordable DVD.

4. Convert video data that you wish to view on a DVD player into the .AVI format using video file format converting software. If you have none, this must be purchased or downloaded. Import the .AVI file into the video editing software and then output the file to the DVD burner. As with the other software, your computer may have come with it; however, it is usually the case that those are lite versions that do not do the tasks well.

5. Import the .AVI file into the video editing software and then output the file to the drive letter of your DVD burner drive. Or for more precision of layout, use the DVD authoring software. As with the other software, your computer may have come with it; however, it is usually the case that those are lite versions that do not do the tasks well.

VHS to DVD

6. Connect your VCR to the three (audio left, right and video) jacks on your computer using the RCA cable. If your VHS tape was encrypted, then place the copy-protection filter box in line between the VCR and the computer. The box is also a signal enhancer that maximizes video signal quality.

7. Open the video capture software on the computer. Select your input source, which is the jacks to which you connected the RCA wire. Select your capture time to match the length of the tape in minutes. Set your VCR to play and click the button to begin capturing video. The capture will take the actual duration of the tape's play-through.

8. Select the option to burn the captured video to the blank DVD.

Tags: your computer, burner drive, cable your, case that, case that those, come with, come with however

Connect Mini Foldable Speakers To My Ipod

A user can listen to an iPod using earphones or by connecting the iPod to a speaker system.

Mini foldable speakers allow an iPod or MP3 user to hear the sound playing from the music device while not wearing headphones. This may be done for personal preference and comfort or to allow more than one user to hear the sound at any time. Mini foldable speakers are small and lightweight, with speakers that can be folded inward or upward for compact storage. Not all mini foldable speakers systems are compatible with every type of Apple iPod. Read the product box prior to purchasing to find out if the speakers are compatible with your iPod type.

Instructions

1. Rotate the mini foldable speakers downward or outward. This process will vary based on the brand and model of speakers you own, however, the speakers will only rotate one way.

2. Press the Apple iPod into the docking station with the bottom of the iPod entering first. The front of the iPod should be facing outward, or in the same direction as the speakers. The iPod should be firmly connected to the docking station.

3. Power on the iPod. The iPod should now play through the speakers. Adjust the volume as needed using the volume up and down buttons on the iPod.

Tags: foldable speakers, iPod should, Apple iPod, compatible with, docking station, hear sound

The Best Ways To Mount A Gps

A GPS can help a lost driver find his or her way in an unfamiliar city. They are so useful that they are becoming standard in new cars. New cars have the GPS built into the dashboard. In older vehicles, the GPS will have to be mounted onto an object. Suction mounts are included with the GPS, but there are other options for mounting a GPS.

Suction Mount

The suction mount is included with all GPS units and is used to mount the GPS to a windshield or dashboard. The mount uses a suction cup with a lever. When the lever is pressed, the suction cup attaches to a black disc that is attached to the windshield or dashboard. Minnesota is the only state that prohibits drivers from mounting the GPS to the windshield. Check with your local government for laws on mounting GPS units. A suction mount can be attached to a dashboard, but the surface must be flat.

Velcro

Velcro with adhesive backing can be used to mount a GPS to a dashboard. Attach a strip of Velcro to the back of the GPS and the dashboard. There are some drawbacks to using Velcro to mount a GPS. If removed, the Velcro can leave a sticky spot on the dashboard. The Velcro may come lose over time and won't be able to hold up the GPS.

Cup Holder Mount

A cup holder mount is put into a cup holder, and the GPS can be mounted to it. Cup holder mounts can be bought or made. They are made by gluing the black disc from the suction cup mount to a piece of PVC pipe. The pipe is placed in the cup holder and the suction mount is attached to it.

Air Vent, Sun Visor, Light Socket Mounts

A GPS can be mounted to the air vent, sun visor or light socket. These mounts are inexpensive and can be bought at any GPS retailer.

Handlebar Mount

A handlebar mount is used to mount a GPS on a motorcycle or bike. The GPS is held onto the handlebar using a u-bolt and nuts. Handlebar mounts can be installed at home. The handlebar mount kits can be purchased at a local GPS retailer.

Tags: used mount, black disc, handlebar mount, included with, mount attached, suction mount, suction mount

Use Dazzle Video

Dazzle Video is hardware that lets you connect a device such as a digital camcorder to your computer in the event your machine doesn't have the necessary inputs like FireWire. You can connect your digital camcorder to the Dazzle Video device using composite video and audio cables, and then plug the Dazzle Video device into a USB port on your computer. This is especially helpful on older machines with older video cards that don't have all of the required inputs necessary for hardware connections.

Instructions

1. Locate the composite video and audio cables that came with your digital camcorders. There will be three cables---one red, one white and one yellow. If your camcorder didn't come with these cables you can find them at any electronics retailer. You can also use the composite cables that are connecting other devices in your home, such as a DVD player to a TV for example, if you don't want to buy additional cables for this one purpose.

2. Plug the composite video cables into your digital camcorder. The red and white cables are audio cables; they go into the red and white audio jacks on your camcorder. The yellow cable is a video cable, and it needs to go into the yellow input on your camcorder.

3. Plug the other ends of the composite video cables into the Dazzle Video device. Match up the colors, and make sure the red, white and yellow cables are plugged into the red, white and yellow inputs on the Dazzle Video device.

4. Plug the USB cable attached to the Dazzle Video device into a USB port on your computer. Any USB port will work for this purpose.

5. Turn on your computer. Your machine will immediately recognize the Dazzle Video device. You can now watch the video from your digital camcorder on your computer, or use a program such as Windows Movie Maker or Adobe Premiere to capture the video to your hard drive.

Tags: Dazzle Video, Dazzle Video device, Video device, your computer, composite video, digital camcorder